We usually make a good profit on the material and charge for the contact cement, which is heat resistant and waterproof. Roll the carpet out completely and with a wax pencil or soap bar make arrows toward one end to ensure you keep the carpet going in the same direction. I always use the bow as my arrow direction. If possible, use the old carpet as a pattern.
Be sure to mark the old carpet with arrows. Magic markers work great for this. Remember that the cutouts for the hatches will be larger than the actual hatch because they are wrapped inside the lip. I drill out the rivet slowly, making sure not to break it off. Make sure you label the bow direction on all removable pieces, and remove and label the locks and hardware.
I place all hardware in plastic bags and mark them. Next we remove the old carpet. I have found the best way is to use a sonic cutter with an old blade as a scraper. Sometimes elbow grease works best. I have seen some people use a high-pressure washer with a rotary nozzle. This will work, but you lose any pattern you might need because the old carpet is destroyed.
Time is the most important factor because you can spend a lot of it removing carpet just to get to the point of starting to put things back together.
Do not use chemicals to dissolve the old glue because they are hard to wash off, and you want a clean surface to make the new contact cement stick. The idea is to keep the carpet all running the same direction, which ensures that the nap is always going the same way. If you take a piece and lay it sideways it will appear a different color or shade. I cut out and label each piece before I start. This way I know I have enough carpet. Begin with laying the largest pieces of carpet first, then work all the deck areas.
When spraying the glue with a simple spray gun, spray the glue past the inside corners where you have to install another piece next to it. This will save you from having to mask off the new carpet. Glue can be brushed with disposable brushes into hard-to-get-to areas.
Mineral spirits will remove overspray on carpet. Please log in with your username or email to continue. No account yet? Create an account. Edit this Article. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy.
Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article methods. Tips and Warnings. Related Articles.
Article Summary. Method 1. Start with a sharp knife. A standard utility knife is preferable, though something like an X-Acto knife or razor can also do the trick. Whatever you use, make sure the edge is nice and sharp. You might also use a handheld electric carpet cutting tool. These tools feature durable edges and automated cutting action, which can help you sidestep the difficulty of doing it manually.
Place the tip of the knife against the carpet. Grip the knife in your dominant hand so that the angled edge of the blade is pointing away from you. Point the blade downward and touch the tip to your starting point on the carpet. Cutting carpet is mostly a matter of getting through the backing, which is the hard, flat side that lays flush against the floor.
You might blunt or break your knife, or even mark up the underlying flooring. Drag the blade along in a straight line. You should be able to feel the backing give way beneath the blade. Use a straightedge to guide your movements, and pause every two or three feet to reposition before you continue cutting.
Following a seam will help you make straight, steady cuts. Replace your knife blade as needed. Your original blade will quickly lose its edge after slicing through multiple feet of tough backing material. To keep the project moving along, be sure to have a new blade on standby. Working with a dull blade will only slow you down. Method 2. Measure your work area. It will also make it easier to cut each section to the proper specifications. Work a few feet at a time.
The key to installing professional-looking carpet is to take your time and give each section the same amount of care and attention. Unroll the carpet as you go, separating it into more manageable strips. Cut two or three feet, then scoot back and resume cutting from a comfortable position. The roll itself can serve as a convenient reference for tracing straight lines. Make your cuts on the backside of the carpet.
They also help specifically protect the wall from being scuffed or damaged by shoes. Trim is a more encompassing term that can include baseboards. Trim applies to any strips of material that are used decoratively throughout the home. Examples of trim include baseboards, crown molding, panel molding, door casing, picture rails, and window trim.
If the baseboards are not removed, the tack strips of the carpet will be laid up until the edge of the trim. The edge of the carpet is then rolled under the edge of the baseboard trim. However, it is important to take your time and be careful while installing the carpet. Some professional carpet installers may prefer to remove the baseboards before installing carpet, but this is simply a matter of preference rather than a necessity.
Usually, this is done so as to avoid damaging the baseboards and to easily ensure the carpet is secured all the way to the wall. Often, you may want to paint your baseboards in order to match walls or add a creative touch to your home. Painting baseboards can be deceptively tricky, so it is helpful to know a few tricks to make the job easier before you decide to begin. Since baseboards generally lack texture, any small flaw in the baseboard will be visible, even after painting.
Because of this, you want to make sure the baseboards are clean and sanded smooth of any blemishes before you begin. It is also important to prime your baseboards if you intend to paint them. Priming also helps flag any troublesome areas you need to fix before you actually apply paint. Some baseboards are pre-primed. With these, you may not need to prime before painting. Priming is not absolutely necessary, but if you choose not to prime your baseboards you may end up having to paint several layers of paint before you reach the desired opacity level.
If your baseboards are somewhere there is a lot of moisture, such as a bathroom, consider using a moisture vapor barrier primer to help protect the baseboards long-term.
For the paint itself, you can choose oil-based, water-based, or an alkyd-acrylic hybrid. Each has advantages and disadvantages:. To paint baseboards, it is often easiest to paint them before installation. You can use brushes, rollers, or a paint sprayer; the choice is usually determined by the type of paint you are using and your personal preference. Before painting, make sure to prepare the baseboards by filling any holes or dents, sanding any grit or imperfections, and thoroughly cleaning the surfaces to ensure a flawless paint job.
When you are installing baseboards, they are usually attached to the wall with nails.
0コメント